![]() ![]() Save the script and launch it (bash script.sh 1024 720 60) you can set the custom resolution with that script but it is a temporary solution whenever you logout and login again you have to run the script again. VIRTUAL1 disconnected (normal left inverted right x axis y axis) HDMI2 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1024圆00+0+0 (normal left inverted right x axis y axis) 697mm x 392mm Screen 0: minimum 8 x 8, current 1024 x 600, maximum 32767 x 32767ĭP1 disconnected (normal left inverted right x axis y axis) 1024圆00.sh, after which, the following will be reported by xrandr(1). Then, create a file with the appropriate commands: # cat > 1024圆00.sh This is what I had to do on an #IntelMaker #Joule in order to make it work in the native resolution with a SUNFOUNDER 7 INCH TFT COLOR MONITOR, which is listed as having 1024*600 resolution, but was picked up as 1280x720 instead.įirst, Intel Joule with Linux 4.4.15-yocto-standard x86_64 doesn't seem to have gtf(1), so, I had to use a different machine to calculate the appropriate numbers: $ gtf 1024 600 60 You can try it out if the above steps seem too complicated for you: I also wrote a script that does all these steps automatically. # Usually unlikely, but if it doesn't apply automatically # It should add the new mode to the display & apply it. # you've set in the previous command (-newmode) # The last parameter is the mode-alias/name which # Run "xrandr" without any parameters to be sure. # VGA1 is the display name, it might differ for you. # Then all you have to do is to add the new mode to the # of the display mode - you can as well pass something # Well, the string within the quotes is the nick/alias # Now, use "xrandr" to make the system recognize a new # Copy this entire string (except for the starting "Modeline") # Typically, it outputs a line starting with "Modeline" # IMPORTANT: BE SURE THE MONITOR SUPPORTS THE RESOLUTION # vertical resolution is 1080px & refresh-rate is 60Hz. # In this case, the horizontal resolution is 1920px the # refresh-rate as the command parameters: # All you have to do is to pass the resolution & the. # Luckily, the tool "gtf" will help you calculate it. # First we need to get the modeline string for xrandr But make sure your monitor and onboard graphics support that resolution. Following steps are for adding a 1920x1080 resolution, but you can use it for any other resolution you want. TLAC was designed for global systemically important banks (G-SIBs) at the international level, and has been formulated differently in some aspects.Here are the steps you need to add a new custom resolution and apply it. MREL pursues the same regulatory aim of ensuring sufficient loss absorbing and recapitalization capacity in resolution as the TLAC standard developed by the Financial Stability Board (FSB). MREL targets are set by EU resolution authorities, after consultation with prudential supervisors, and should be complied with by banks at the end of the transitional period, if any. The BRRD requires that MREL is tailored to bank-specific features, including its size, business model, funding model and risk profile and the needs identified to implement the resolution strategy. This requirement is part of the necessary steps needed to make institutions resolvable. Failure to meet MREL may negatively impact institutions' loss absorption and recapitalisation capacity and, ultimately, the overall effectiveness of resolution. The Bank Recovery and Resolution Directive (BRRD) provides that institutions established in the European Union (EU) should meet a minimum requirement for own funds and eligible liabilities (‘MREL’) to ensure an effective and credible application of the bail-in tool. Thematic register of Appeal Panel decisions. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |